PDF associated:
/741-768_IS.pdf
1 ATTENTION Refer to the appropriate shop manual for your vehicle to obtain specifi c service procedures for this part If you do not have a service manual or lack the skill to install this part it is recommended that you seek the services of a qualifi ed technician Pay special attention to all cautions and warnings included in the shop manual Read and follow all instructions carefully 741 768 INSTALL REMOVAL INSTRUCTIONS WINDOW REGULATOR Disclaimer Even though every attempt is made to ensure this information is complete and accurate it is impossible to account for all possible circumstances or situations Please consult with a qualifi ed auto technician before attempting to perform any work you are not qualifi ed to do Automobiles can be hazardous to work on be sure to take all necessary safety precautions Failure to do so may result in property damage or personal injury Certain motor vehicle standards and performance requirements may apply to your motor vehicle such as Federal Motor Vehicle Safety Standards by the National Highway Traffi c Safety Administration Be sure that your work is performed in accordance with such standards and that you do not disable any motor vehicle safety feature REMOVAL INSTALL OF WINDOW REGULATOR 741 768 Jeep Cherokee 1997 2001 Tools required for removal and installation of window regulator and motor assembly Silicone spray lubricant Panel retainer remover Pick Saddle cup assembly tape or wedge to hold window in place Flat blade screwdriver or plastic pry tool 10mm socket or driver Phillips screwdriver PLEASE WEAR SAFETY GLASSES General Tech Tips Use painter s tape rather than duct tape to secure window It will not damage paint or leave sticky residue A plastic pry tool is useful It will not easily damage delicate trim like a screwdriver or metal pry bar The replacement regulator should have a liberal amount of grease on slide area If there is not much grease present white lithium grease works well to lubricate the slide area Aftermarket window tinting can cause the window to travel slower and put additional strain on the window regulator assembly Window run channels should be cleaned and lubricated before installation of a new window regulator assembly Silicone spray works well 2 ATTENTION Refer to the appropriate shop manual for your vehicle to obtain specifi c service procedures for this part If you do not have a service manual or lack the skill to install this part it is recommended that you seek the services of a qualifi ed technician Pay special attention to all cautions and warnings included in the shop manual Read and follow all instructions carefully 741 768 INSTALL REMOVAL INSTRUCTIONS WINDOW REGULATOR Disclaimer Even though every attempt is made to ensure this information is complete and accurate it is impossible to account for all possible circumstances or situations Please consult with a qualifi ed auto technician before attempting to perform any work you are not qualifi ed to do Automobiles can be hazardous to work on be sure to take all necessary safety precautions Failure to do so may result in property damage or personal injury Certain motor vehicle standards and performance requirements may apply to your motor vehicle such as Federal Motor Vehicle Safety Standards by the National Highway Traffi c Safety Administration Be sure that your work is performed in accordance with such standards and that you do not disable any motor vehicle safety feature Removal Instructions STEP 1 Gain access to the window regulator assembly by removing the interior trim panel STEP 1a Remove the screws attaching the interior door trim panel to the inner door STEP 1b Separate the interior door panel fasteners from the interior door using a panel retainer remover 3 ATTENTION Refer to the appropriate shop manual for your vehicle to obtain specifi c service procedures for this part If you do not have a service manual or lack the skill to install this part it is recommended that you seek the services of a qualifi ed technician Pay special attention to all cautions and warnings included in the shop manual Read and follow all instructions carefully 741 768 INSTALL REMOVAL INSTRUCTIONS WINDOW REGULATOR Disclaimer Even though every attempt is made to ensure this information is complete and accurate it is impossible to account for all possible circumstances or situations Please consult with a qualifi ed auto technician before attempting to perform any work you are not qualifi ed to do Automobiles can be hazardous to work on be sure to take all necessary safety precautions Failure to do so may result in property damage or personal injury Certain motor vehicle standards and performance requirements may apply to your motor vehicle such as Federal Motor Vehicle Safety Standards by the National Highway Traffi c Safety Administration Be sure that your work is performed in accordance with such standards and that you do not disable any motor vehicle safety feature STEP 2 Lift the trim panel up and outward to separate the trim panel from the interior window belt seal STEP 3 Move the door trim panel outward and disconnect the interior door handle to latch rod retaining clips STEP 4 Disconnect the power door locks power window power mirror wire harness connectors if equipped 4 ATTENTION Refer to the appropriate shop manual for your vehicle to obtain specifi c service procedures for this part If you do not have a service manual or lack the skill to install this part it is recommended that you seek the services of a qualifi ed technician Pay special attention to all cautions and warnings included in the shop manual Read and follow all instructions carefully 741 768 INSTALL REMOVAL INSTRUCTIONS WINDOW REGULATOR Disclaimer Even though every attempt is made to ensure this information is complete and accurate it is impossible to account for all possible circumstances or situations Please consult with a qualifi ed auto technician before attempting to perform any work you are not qualifi ed to do Automobiles can be hazardous to work on be sure to take all necessary safety precautions Failure to do so may result in property damage or personal injury Certain motor vehicle standards and performance requirements may apply to your motor vehicle such as Federal Motor Vehicle Safety Standards by the National Highway Traffi c Safety Administration Be sure that your work is performed in accordance with such standards and that you do not disable any motor vehicle safety feature STEP 5 Remove the door panel from the door STEP 6 Remove the vapor barrier NOTE The vapor barrier is attached to the door panel using a Butyl adhesive a black sticky adhesive that has the appearance of caulk STEP 6a Disengage the clips attaching the wiring harness to the door inner panel STEP 6b Grasp the upper and lower rearward corners of the vapor barrier and rapidly peel back the vapor barrier from the door inner panel STEP 6c Separate the vapor barrier from the door inner panel 5 ATTENTION Refer to the appropriate shop manual for your vehicle to obtain specifi c service procedures for this part If you do not have a service manual or lack the skill to install this part it is recommended that you seek the services of a qualifi ed technician Pay special attention to all cautions and warnings included in the shop manual Read and follow all instructions carefully 741 768 INSTALL REMOVAL INSTRUCTIONS WINDOW REGULATOR Disclaimer Even though every attempt is made to ensure this information is complete and accurate it is impossible to account for all possible circumstances or situations Please consult with a qualifi ed auto technician before attempting to perform any work you are not qualifi ed to do Automobiles can be hazardous to work on be sure to take all necessary safety precautions Failure to do so may result in property damage or personal injury Certain motor vehicle standards and performance requirements may apply to your motor vehicle such as Federal Motor Vehicle Safety Standards by the National Highway Traffi c Safety Administration Be sure that your work is performed in accordance with such standards and that you do not disable any motor vehicle safety feature STEP 7 Using either painter s tape saddle cup assembly or a window glass wedge disconnect the window glass from the window regulator assembly STEP 8 Loosen the bolts attaching the regulator to the inner door panel STEP 9 Lift the regulator upward to release it from the keyed hole slots and remove the regulator through the access hole in the door inner panel 6 ATTENTION Refer to the appropriate shop manual for your vehicle to obtain specifi c service procedures for this part If you do not have a service manual or lack the skill to install this part it is recommended that you seek the services of a qualifi ed technician Pay special attention to all cautions and warnings included in the shop manual Read and follow all instructions carefully 741 768 INSTALL REMOVAL INSTRUCTIONS WINDOW REGULATOR Disclaimer Even though every attempt is made to ensure this information is complete and accurate it is impossible to account for all possible circumstances or situations Please consult with a qualifi ed auto technician before attempting to perform any work you are not qualifi ed to do Automobiles can be hazardous to work on be sure to take all necessary safety precautions Failure to do so may result in property damage or personal injury Certain motor vehicle standards and performance requirements may apply to your motor vehicle such as Federal Motor Vehicle Safety Standards by the National Highway Traffi c Safety Administration Be sure that your work is performed in accordance with such standards and that you do not disable any motor vehicle safety feature Installation Instructions STEP 1 Insert the window regulator through the access hole STEP 1a Position the regulator in the door and align the regulator in the keyed hole slots in the door interior panel STEP 1b Attach the regulator to the door interior panel with the attachment bolts STEP 2 Attach the window glass to the window regulator STEP 3 Re attach the vapor barrier to the door interior panel STEP 3a Attach the wiring harness to the interior door panel STEP 4 Connect the harness connector to the power window door lock power mirror switch if so equipped 7 ATTENTION Refer to the appropriate shop manual for your vehicle to obtain specifi c service procedures for this part If you do not have a service manual or lack the skill to install this part it is recommended that you seek the services of a qualifi ed technician Pay special attention to all cautions and warnings included in the shop manual Read and follow all instructions carefully 741 768 INSTALL REMOVAL INSTRUCTIONS WINDOW REGULATOR Disclaimer Even though every attempt is made to ensure this information is complete and accurate it is impossible to account for all possible circumstances or situations Please consult with a qualifi ed auto technician before attempting to perform any work you are not qualifi ed to do Automobiles can be hazardous to work on be sure to take all necessary safety precautions Failure to do so may result in property damage or personal injury Certain motor vehicle standards and performance requirements may apply to your motor vehicle such as Federal Motor Vehicle Safety Standards by the National Highway Traffi c Safety Administration Be sure that your work is performed in accordance with such standards and that you do not disable any motor vehicle safety feature STEP 5 Attach the door handle to door latch connecting rods STEP 6 Verify that the new regulator is in operating order there is no binding and that the glass operates properly in the UP and DOWN positions STEP 7 In a downward motion insert the door trim panel onto the inner window belt seal 8 ATTENTION Refer to the appropriate shop manual for your vehicle to obtain specifi c service procedures for this part If you do not have a service manual or lack the skill to install this part it is recommended that you seek the services of a qualifi ed technician Pay special attention to all cautions and warnings included in the shop manual Read and follow all instructions carefully 741 768 INSTALL REMOVAL INSTRUCTIONS WINDOW REGULATOR Disclaimer Even though every attempt is made to ensure this information is complete and accurate it is impossible to account for all possible circumstances or situations Please consult with a qualifi ed auto technician before attempting to perform any work you are not qualifi ed to do Automobiles can be hazardous to work on be sure to take all necessary safety precautions Failure to do so may result in property damage or personal injury Certain motor vehicle standards and performance requirements may apply to your motor vehicle such as Federal Motor Vehicle Safety Standards by the National Highway Traffi c Safety Administration Be sure that your work is performed in accordance with such standards and that you do not disable any motor vehicle safety feature STEP 8 Align door trim panel fasteners into the holes on the door STEP 9 With equal and fi rm pressure push the door panel onto the door STEP 10 Re install the screws into the corresponding holes in the interior trim panel Be sure that the screws are aligned properly so that you do not cross thread the door We appreciate your opinions regarding this product Please call our Technical Assistant with any challenges or suggestions regarding the installation or operation of this product 1 800 523 2492
