PDF associated:
/37096-installation-instructions.pdf
FULL SIZE TRUCK MULTI FIT HITCH Model Number 37096 Quick and Easy Installation Many NO DRILL Applications No Special Tools Required for Installation Unique OEM Protective Coating This Instruction Sheet contains IMPORTANT safety information Please read and keep for future reference Use ONLY REESE supplied or approved bolts locknuts and washer to install this hitch THIS WARNING IS GIVEN IN COMPLIANCE WITH CALIFORNIA PROPOSITION 65 WARNING This product contains chemicals known to the state of California to cause cancer birth defects or other reproductive harm READ and Follow all Instructions and safety messages before installing the Multi Fit Hitch Failure to follow these instructions may result in DEATH or SERIOUS INJURY DO NOT lubricate threads Bolt failure may occur due to over tightening DO NOT drill or weld to this hitch This product complies with safety specification and requirements for the State of New York and VESC regulation V 5 for connecting devices and towing systems Weight distributing hitch rating is 6500 lb maximum gross trailer weight and 650 lb maximum tongue weight Weight carrying hitch rating is 5000 lb maximum gross trailer weight and 500 lb maximum tongue weight Consult vehicle owners manual for towing recommendations and limitations Qty 4 CENTER SECTION LOCK NUT 1 2 1 3 Qty 2 HEX HEAD BOLT M14 X 2 00 X 45mm CL 10 9 Qty 4 CARRIAGE BOLT 1 2 13 X 1 25 GR 8 Qty 4 BOLT PLATE 1 4 X 1 5 X 3 Qty 2 LOCKWASHER 9 16 Qty 2 HEX NUT M12 X 1 75 CL 8 Qty 2 CARRIAGE BOLT 1 2 13 X 2 25 GR 5 Qty 8 BOLT PLATE 3 8 X 1 25 X 2 5 Qty 8 HEX HEAD BOLT 3 8 16 X 1 25 GR5 Qty 4 BOLT PLATE 1 4 X 1 0 X 1 5 Qty 2 HEX HEAD BOLT 1 2 13 X 2 25 GR 5 Qty 4 BOLT PLATE 1 4 X 1 0 X 2 0 Qty 6 CONICAL WASHER 1 2 Qty 4 HEX NUT 1 2 13 Qty 2 HEX HEAD BOLT M12 X 1 75 X 45mm CL 10 9 Qty 8 WASHER NUTS 3 8 16 FASTENER KIT CONTAINS THE BELOW ITEMS METRIC METRIC METRIC GENERAL INSTRUCTIONS 1 Remove center section from box and pull side plate assemblies from shipping location Insert side plate assemblies into hitch center section Refer to specific instructions for proper position Insert the coiled end of pull wire through hole on rear side of center section and through end of tube Attach 1 4 bolt plate and 1 2 x 1 1 4 long carriage bolt as shown above Pull fasteners through and loosely install 1 2 hex lock nut Repeat steps for each fastener The spare tire may need to be lowered to install the hitch It will be replaced later 2 Refer to the application chart to determine the correct installation for your vehicle Last page of each language FOR ALL INSTALLATIONS UNLESS OTHER WISE NOTED 1 Torque all 3 8 nuts to 35 lb ft 5 Torque all 10mm CL10 9 hardware to 53 lb ft 2 Torque all 12mm nuts bolts to 65 lb ft 6 Torque all 5 8 hardware to 100 lb ft 3 Torque all 1 2 hardware to 75 lb ft 7 Torque all 14mm CL10 9 hardware to 115 lb ft 4 Torque 4 center section locknuts to 110 lb ft 8 Retighten the spare tire if it was loosened NOTE Not all of the hardware will be used in every installation Paint any bare metal to prevent rust TOOLS REQUIRED 3 4 SOCKET WRENCH 9 16 SOCKET WRENCH 15MM 17MM 18 MM SOCKET 19MM 21MM 22MM SOCKET TORQUE WRENCH SAFETY GLASSES SIDE PLATE ASSEMBLY UP SEE SPECIFIC INSTRUCTIONS FOR PROPER SIDE PLATE ASSEMBLY POSITION UP OR DOWN MUST INSTALL REAR SIDE BOLT FIRST 1 2 x 1 1 4 CARRIAGE BOLT 1 4 x 1 x 2 BOLT PLATE 1 2 HEX LOCKNUT PULL WIRE SUPPLIED CENTER SECTION CENTER SECTION LOCKNUT CENTER SECTION LOCK NUT CENTER SECTION ASSEMBLY TOOLS REQUIRED 9 16 3 4 SOCKET 21MM SOCKET TORQUE WRENCH SAFETY GLASSES VEHICLE FRAME 1 4 x 1 1 2 x 3 BOLT PLATE 99 13 CHEVROLET SILVERADO GMC SIERRA 1500 PICKUP 1 Remove the two 2 rear M14 bumper bracket bolts 2 Raise hitch side brackets into position aligning hole 2 in bracket with the rear most weldnut in frame 3 Install the M14 X 45 MM hex bolt 9 16 lock washer and 3 8 bolt plate though hole 2 and into weldnut in frame both sides finger tight 4 Install 1 2 x 2 1 4 carriage bolt and block into forward hole of frame that aligns with hole 5 in hitch side bracket as shown 5 Install 3 8 bolt plate 1 2 conical washer and nut both sides finger tight 6 Install center section as pre assembled on front page with 4 3 8 x 1 bolts and washer nuts both sides Align center section of hitch with center of vehicle Finger tighten fasteners 7 Tighten hitch side bracket to frame Tighten side plate assembly to side bracket Tighten side bracket assembly to center section HOLE 5 HOLE 2 3 8 x 1 1 4 bolt 3 8 WASHER NUTS SIDE PLATE ASSEMBLY CENTER SECTION HITCH SIDE BRACKET NOTE General assembly loosely assemble center section page 1 loosely install side brackets on vehicle this page install center section assembly tighten all fasteners to proper specifications page 1 3 8 x 1 1 4 x 2 1 2 BOLT PLATE 1 2 X 2 1 4 CARRIAGE BOLT M14 X 45MM CL10 9 BOLT EXISTING WELDNUT ON BUMPER BRACKET 1 2 CONICAL WASHER 1 2 NUT 9 16 LOCK WASHER 3 8 x 1 1 4 x 2 1 2 BOLT PLATE INSTALLATION A TOOLS REQUIRED 9 16 3 4 SOCKET 21MM SOCKET TORQUE WRENCH SAFETY GLASSES VEHICLE FRAME 1 4 x 1 1 2 x 3 BOLT PLATE 01 07 CHEVROLET SILVERADO GMC SIERRA 2500HD PICKUP 07 CLASSIC ONLY 1 Remove the two 2 rear most M14 bumper bracket bolts 2 Raise hitch side brackets and 3 8 bolt plate into position aligning hole 3 in bracket with the rear most weldnut in frame 3 Install the M14 x 45mm hex bolt and 9 16 lock washer though hole 3 and into weldnut in frame both sides finger tight 4 Install 1 2 x 2 1 4 carriage bolt and block into hole of frame that aligns with hole 4 in hitch side bracket as shown 5 Install 1 2 x 2 1 4 hex bolt and block into hole of frame that aligns with hole 2 in hitch side bracket as shown 6 Install 3 8 bolt plate between frame and hitch side bracket at hole 2 and 4 as shown 7 Finger tighten 1 2 conical washer and nut both sides 8 Install center section as pre assembled on front page with 4 3 8 x 1 bolts and washer nuts both sides Align center section of hitch with center of vehicle Finger tighten fasteners 9 Tighten hitch side bracket to frame Tighten side plate assembly to side bracket Tighten side bracket assembly to center section HOLE 4 HOLE 2 3 8 x 1 1 4 bolt 3 8 WASHER NUTS SIDE PLATE ASSEMBLY CENTER SECTION HITCH SIDE BRACKET NOTE General assembly loosely assemble center section page 1 loosely install side brackets on vehicle this page install center section assembly tighten all fasteners to proper specifications page 1 3 8 x 1 1 4 x 2 1 2 BOLT PLATE 1 2 X 2 1 4 CARRIAGE BOLT M14 X 45mm BOLT EXISTING WELDNUT ON BUMPER BRACKET 1 2 CONICAL WASHER 1 2 NUT HOLE 3 1 2 NUT 1 2 CONICAL WASHER 9 16 LOCK WASHER 1 2 x 2 1 4 HEX BOLT INSTALLATION B TOOLS REQUIRED 9 16 3 4 SOCKET 18MM SOCKET TORQUE WRENCH SAFETY GLASSES VEHICLE FRAME 1 4 x 1 1 2 x 3 BOLT PLATE 97 04 FORD F 150 PICKUP OLD BODY STYLE 1 Lower spare tire 2 Place 1 2 x 2 1 4 bolts and 1 4 bolt plate in rear most hole in frame Both sides 3 Aligning hole 1 in bracket with the rear most hole in frame Raise hitch side bracket 3 8 bolt plate 1 2 conical washer and 1 2 nut into position both sides loosely install nut 4 Install the 1 2 x 2 1 4 carriage bolt and 1 4 bolt plate though hole in frame that aligns with hole 5 in hitch side bracket Install 3 8 bolt plate 1 2 conical washer and 1 2 nut both sides loosely install nut 5 Install the M12 x 45mm hex bolt and 1 4 bolt plate though hole in frame that aligns with hole 4 in hitch side bracket Install 1 2 conical washer and m12 nut both sides finger tight 6 Install center section as pre assembled on front page with 4 3 8 x 1 bolts and washer nuts both sides Align center section of hitch with center of vehicle Finger tighten fasteners 7 Tighten hitch side bracket to frame Tighten side plate assembly to side bracket Tighten side bracket assembly to center section 8 Raise spare tire back into place HOLE 5 HOLE 1 3 8 x 1 1 4 bolt 3 8 WASHER NUTS SIDE PLATE ASSEMBLY CENTER SECTION HITCH SIDE BRACKET NOTE General assembly loosely assemble center section page 1 loosely install side brackets on vehicle this page install center section assembly tighten all fasteners to proper specifications page 1 3 8 x 1 1 4 x 2 1 2 BOLT PLATE 1 2 X 2 1 4 CARRIAGE BOLT 1 2 CONICAL WASHER 1 2 NUT 1 2 CONICAL WASHER 1 2 NUT 3 8 x 1 1 4 x 2 1 2 BOLT PLATE 1 2 CONICAL WASHER 1 2 NUT 1 2 x 2 1 4 HEX BOLT 3 8 x 1 1 4 x 2 1 2 BOLT PLATE M12 NUT 1 2 CONICAL WASHER M12 X 45MM BOLT 1 4 X 1 X 1 1 2 BOLT PLATE HOLE 4 EXISTING HOLES INSTALLATION C TOOLS REQUIRED 9 16 3 4 SOCKET 1 2 DRILL BIT 18MM SOCKET TORQUE WRENCH SAFETY GLASSES VEHICLE FRAME 1 4 x 1 1 2 x 3 BOLT PLATE 99 04 FORD F 250 F 350 SUPER DUTY PICKUP 1 Lower spare tire 2 Place 1 2 x 2 1 4 bolts and 1 4 bolt plates in noted existing holes in frame Both sides 3 Aligning hole 3 and 4 in bracket with bolts in frame Raise hitch side bracket 3 8 bolt plate 1 2 conical washer and 1 2 nut into position as shown both sides loosely install nuts 4 Using hole 1 in bracket as a guide drill a 1 2 hole in frame 5 Install the M12 x 45mm hex bolt and 1 4 bolt plate though hole in frame Install 1 2 conical washer and M12 nut both sides finger tight 6 Install center section as pre assembled on front page with 4 3 8 x 1 bolts and washer nuts both sides Align center section of hitch with center of vehicle Finger tighten fasteners 7 Tighten hitch side bracket to frame Tighten side plate assembly to side bracket Tighten side bracket assembly to center section 8 Raise spare tire back into place HOLE 1 3 8 x 1 1 4 bolt 3 8 WASHER NUTS SIDE PLATE ASSEMBLY CENTER SECTION HITCH SIDE BRACKET NOTE General assembly loosely assemble center section page 1 loosely install side brackets on vehicle this page install center section assembly tighten all fasteners to proper specifications page 1 3 8 x 1 1 4 x 2 1 2 BOLT PLATE 1 2 X 2 1 4 CARRIAGE BOLT 1 2 NUT 1 2 CONICAL WASHER 1 2 CONICAL WASHER 1 2 NUT 1 2 x 2 1 4 HEX BOLT 3 8 x 1 1 4 x 2 1 2 BOLT PLATE M12 NUT M12 X 45MM BOLT 1 4 X 1 X 1 1 2 BOLT PLATE HOLE 4 EXISTING HOLES DRILLED HOLE HOLE 3 INSTALLATION E TOOLS REQUIRED 9 16 3 4 SOCKET 1 2 DRILL BIT 18MM SOCKET TORQUE WRENCH SAFETY GLASSES 94 01 DODGE 1500 PICKUP 94 02 DODGE 2500 3500 PICKUP SHORT BED 1 Lower spare tire 2 Place 1 2 x 2 1 4 carriage bolts and 1 4 bolt plates in noted existing large hole in end of frame Both sides 3 Aligning hole 1 in bracket with bolts in frame Raise 3 8 bolt plate hitch side bracket 1 4 bolt plate 1 2 conical washer and 1 2 nut into position as shown both sides loosely install nuts 4 Pull both hitch side brackets to the rear most of hole in frame 5 If the vehicle frame has a hole that lines up with hole 4 in hitch side bracket install fasteners and bolt plates as shown If hole doesn t exist or is to small drill 1 2 hole in vehicle frame approximatly centered in 4 hole if small hole doesn t exist Install fasteners and bolt plates as shown 6 Using hole 3 in bracket as a guide drill a 1 2 hole in frame Make sure that there is enough room to place 1 4 x 1 x 1 1 2 bolt plate flat on the inside of the frame next to the frame cross member 7 Install the M12 x 45mm hex bolt and 1 4 bolt plate though hole in frame Install 3 8 bolt plate 1 2 conical washer and M12 nut as shown both sides finger tight 8 Install center section as pre assembled on front page with 4 3 8 x 1 bolts and washer nuts both sides Align center section of hitch with center of vehicle Finger tighten fasteners 9 Tighten hitch side bracket to frame Tighten side plate assembly to hitch side bracket Tighten side plate assembly to center section 10 Raise spare tire back into place NOTE General assembly loosely assemble center section page 1 loosely install side brackets on vehicle this page install center section assembly tighten all fasteners to proper specifications page 1 VEHICLE FRAME 1 4 x 1 1 2 x 3 BOLT PLATE HOLE 1 3 8 x 1 1 4 BOLT 3 8 WASHER NUTS SIDE PLATE ASSEMBLY CENTER SECTION HITCH SIDE BRACKET 3 8 x 1 1 4 x 2 1 2 BOLT PLATE 1 2 X 2 1 4 CARRIAGE BOLT 1 2 NUT 1 2 CONICAL WASHER 1 2 CONICAL WASHER 1 2 NUT 1 2 x 2 1 4 HEX BOLT 3 8 x 1 1 4 x 2 1 2 BOLT PLATE M12 NUT M12 X 45MM BOLT HOLE 4 EXISTING HOLES DRILLED HOLE ON SOME MODELS HOLE 3 DRILLED HOLE 1 2 CONICAL WASHER 1 4 x 1 1 2 x 3 BOLT PLATE 1 4 X 1 X 1 1 2 BOLT PLATE 1 4 x 1 1 2 x 3 BOLT PLATE 1 4 X 1 X 1 1 2 BOLT PLATE 3 8 x 1 1 4 x 2 1 2 BOLT PLATE 1 2 x 2 1 4 HEX BOLT M12 X 45MM BOLT 1 2 X 2 1 4 CARRIAGE BOLT 3 8 x 1 1 4 BOLT FRAME CROSS MEMBER SUSPENSION SUPPORT HEAVY DUTY MODELS ONLY INSTALLATION F TOOLS REQUIRED 9 16 3 4 SOCKET 1 2 DRILL BIT 18MM SOCKET TORQUE WRENCH SAFETY GLASSES 94 01 DODGE 1500 PICKUP 94 02 DODGE 2500 3500 PICKUP LONG BED 1 Lower spare tire 2 Place 1 2 x 2 1 4 carriage bolts and 1 4 bolt plates in noted existing large hole in end of frame Both sides 3 Aligning hole 1 in bracket with bolts in frame Raise 3 8 bolt plate hitch side bracket 1 4 bolt plate 1 2 conical washer and 1 2 nut into position as shown both sides loosely install nuts 4 Pull both hitch side brackets to the forward most of hole in frame 5 If the vehicle frame has a hole that lines up with hole 4 in hitch side bracket install fasteners and bolt plates as shown If hole doesn t exist or is to small drill 1 2 hole in vehicle frame approximatly centered in 4 hole Install fasteners and bolt plates as shown 6 Using hole 3 in bracket as a guide drill a 1 2 hole in frame Make sure that there is enough room to place 1 4 x 1 x 1 1 2 bolt plate flat on the inside of the frame 7 Install the M12 x 45mm hex bolt and 1 4 bolt plate though hole in frame Install 3 8 bolt plate 1 2 conical washer and M12 nut as shown both sides finger tight 8 Install center section as pre assembled on front page with 4 3 8 x 1 bolts and washer nuts both sides Align center section of hitch with center of vehicle Finger tighten fasteners 9 Tighten hitch side bracket to frame Tighten side plate assembly to hitch side bracket Tighten side plate assembly to center section 10 Raise spare tire back into place NOTE General assembly loosely assemble center section page 1 loosely install side brackets on vehicle this page install center section assembly tighten all fasteners to proper specifications page 1 VEHICLE FRAME 1 4 x 1 1 2 x 3 BOLT PLATE HOLE 1 3 8 x 1 1 4 BOLT 3 8 WASHER NUTS SIDE PLATE ASSEMBLY CENTER SECTION HITCH SIDE BRACKET 3 8 x 1 1 4 x 2 1 2 BOLT PLATE 1 2 X 2 1 4 CARRIAGE BOLT 1 2 NUT 1 2 CONICAL WASHER 1 2 CONICAL WASHER 1 2 NUT 1 2 x 2 1 4 HEX BOLT 3 8 x 1 1 4 x 2 1 2 BOLT PLATE M12 NUT M12 X 45MM BOLT HOLE 4 EXISTING HOLES DRILLED HOLE ON SOME MODELS HOLE 3 DRILLED HOLE 1 2 CONICAL WASHER 1 4 x 1 1 2 x 3 BOLT PLATE 1 4 X 1 X 1 1 2 BOLT PLATE 1 4 x 1 1 2 x 3 BOLT PLATE 1 4 X 1 X 1 1 2 BOLT PLATE 3 8 x 1 1 4 x 2 1 2 BOLT PLATE 1 2 x 2 1 4 HEX BOLT M12 X 45MM BOLT 1 2 X 2 1 4 CARRIAGE BOLT 3 8 x 1 1 4 BOLT FRAME CROSS MEMBER SUSPENSION SUPPORT HEAVY DUTY MODELS ONLY INSTALLATION G 3 8 x 1 1 4 bolt CENTER SECTION 1 2 X 2 1 4 HEX BOLT 1 2 CONICAL WASHER 3 8 WASHER NUTS SIDE PLATE ASSEMBLY HITCH SIDE BRACKET 3 8 x 1 1 4 x 2 1 2 BOLT PLATE HOLE 2 SHORT BED HOLE 5 SHORT BED VEHICLE FRAME HOLE 4 LONG BED HOLE 1 LONG BED 1 2 NUT 1 4 x 1 x 3 BOLT PLATE 3 8 x 1 1 4 x 2 1 2 BOLT PLATE 3 8 x 1 1 4 x 2 1 2 BOLT PLATE 1 2 CONICAL WASHER 1 2 X 2 1 4 CARRIAGE BOLT HOLE 3 TOOLS REQUIRED 9 16 3 4 SOCKET TORQUE WRENCH SAFETY GLASSES 88 00 CHEVY GMC C K PICKUP SERIES CLASSIC 1 Lower spare tire 2 If your vehicle has rivets on the bottom of the frame you will need to install one 3 8 thick spacer between the frame and hitch side bracket at each bolting location These are needed for clearance between the bracket and the rivet head The bracket cannot be bolted directly against the rivets 3 Install 1 2 X 2 1 4 hex bolt 1 2 conical washer and 3 8 thick spacer with the head on the bottom of the frame Finger tighten 1 2 conical washer and 1 2 nut on each bolt For short beds use hole 2 For long beds use hole 1 NOTE SOME DUAL PIPE EXHAUST SYSTEMS WILL HIT THE BRACKET THE EXHAUST WILL NEED TO BE MODIFIED 4 Short Beds Insert 1 2 carriage bolts with bolt plates down through the 1 diameter hole in the frame and into hole 5 in the hitch side bracket Finger tighten 1 2 conical washer and 1 2 nut on each bolt 5 Long Beds Insert 1 2 carriage bolts with bolt plates down through the 1 diameter hole in the frame and into hole 4 in the hitch side bracket Finger tighten 1 2 conical washer and 1 2 nut on each bolt 6 Install center section as pre assembled on front page with 4 3 8 X 1 1 4 bolts and washer nuts both sides Align center section of hitch with center of vehicle Finger tighten fasteners 7 Tighten hitch side brackets to vehicle frame Tighten side plate assemblies to side brackets Tighten side bracket assemblies to center section Refer to front page for specified torque values 8 Raise spare tire back into place 9 Be sure the spare tire in not rubbing against the brake hose If needed bend the hose mounting bracket to ensure proper clearance NOTE General assembly loosely assemble center section page 1 loosely install side brackets on vehicle this page install center section assembly tighten all fasteners to proper specifications page 1 INSTALLATION H VEHICLE FRAME HOLE 5 HOLE 2 3 8 x 1 1 4 bolt CENTER SECTION 1 4 x x 1 x 1 1 2 BOLT PLATE 12MM HEX BOLT M12 NUT 1 2 X 2 1 4 HEX BOLT 1 4 x 1 x 1 1 2 BOLT PLATE 1 2 CONICAL WASHER 1 2 NUT 3 8 x 1 1 4 x 2 1 2 BOLT PLATE 3 8 WASHER NUTS SIDE PLATE ASSEMBLY HITCH SIDE BRACKET 3 8 x 1 1 4 x 2 1 2 BOLT PLATE 1 2 CONICAL WASHER 3 8 x 1 1 4 x 2 1 2 BOLT PLATE TOOLS REQUIRED 9 16 3 4 18MM SOCKET 1 4 1 2 DRILL BIT 1 2 DRILL TORQUE WRENCH SAFETY GLASSES 87 96 Ford Full Size Pickup 1997 F 250 Heavy Duty F 350 Heavy Duty 1 Lower spare tire 2 Apply masking tape to the bottom of frame in area A and area B Same on both frame rails 3 Measure from the outside of the frame inward 1 and make a line in area A and area B 4 Measure from the rear of the frame forward 3 4 and make a line in area A From that mark measure 14 5 8 forward and make a mark in area B 5 Hold side bracket up to bottom of frame Double check hole 2 and 5 in side bracket for proper alignment with marks If they don t line up adjust the marks in area B 6 Center punch and pilot drill with 1 4 drill bit Enlarge the pilot hole with 1 2 drill bit Total of 4 holes 2 per frame rail 7 Install 12MM hex bolt and block into the hole of frame that aligns with hole 5 in hitch side bracket as shown 8 Install 1 2 X 2 1 4 hex bolt and block into the hole of frame that aligns with hole 2 in hitch side bracket as shown 9 Install 3 8 bolt plate between frame and hitch side bracket at hole 2 and 5 as shown 10 At hole 2 place 3 8 bolt plate underneath hitch side bracket and finger tighten 1 2 conical washer and nut both sides 11 At hole 5 finger tighten 1 2 conical washer and nut both sides 12 Install center section as pre assembled on front page with 4 3 8 X 1 1 4 bolts and washer nuts both sides Align center section of hitch with center of vehicle Finger tighten fasteners 13 Tighten hitch side brackets to vehicle frame Tighten side plate assemblies to side brackets Tighten side bracket assemblies to center section Refer to front page for specified torque values 14 Raise spare tire back into place NOTE General assembly loosely assemble center section page 1 loosely install side brackets on vehicle this page install center section assembly tighten all fasteners to proper specifications page 1 BOTTOM VIEW OF DRIVER SIDE FRAME AREA B 1 2 DRILLED HOLE AREA A 1 2 DRILLED HOLE FORWARD REAR OF FRAME RIVET INSTALLATION I 37096 REESE TOWPOWER MULTI FIT APPLICATION CHART MAKE MODEL MODEL YEARS 87 88 89 90 91 92 93 94 95 96 97 98 99 00 01 02 03 04 05 06 07 08 09 10 11 12 13 14 CHEVROLET SILVERADO 1500 PICKUP A A A A A A A A A A A A A A A CHEVROLET SILVERADO 2500HD PICKUP B B B B B B B CHEVROLET C K SERIES PICKUP CLASSIC H H H H H H H H H H H H H DODGE FULL SIZE PICKUP 1500 SHORTBED F F F F F F F F DODGE FULL SIZE PICKUP 2500 3500 SHORTBED F F F F F F F F F DODGE FULL SIZE PICKUP 1500 LONGBED G G G G G G G G DODGE FULL SIZE PICKUP 2500 3500 LONGBED G G G G G G G G G FORD F 150 PICKUP OLD BODY SYLE I I I I I I I I I I C C C C C C C C FORD F 250 350 SUPER DUTY PICKUP I I I I I I I I I I I E E E E E E E E E E E E E E E E GMC SIERRA 1500 PICKUP A A A A A A A A A A A A A A A GMC SIERRA 2500HD PICKUP B B B B B B B GMC C K SERIES PICKUP CLASSIC H H H H H H H H H H H H H
