PDF associated:
/Lisle_Tool_Supplement_T83new_C4DAFF9F837A1.pdf
PAGE 65 Important This Catalog Supplement introduces new tools not included in Catalog T 72 Supplements T 73 through T 82 Supplement T 83 New No Slip Filter Wrench Tough Stainless Steel Band with Permanently Bonded Textured Coating for Superior Gripping Power won t Slip Swivel handle makes it easy to turn in tight spots Handle swivels more than 180 with adjustable tension Tension adjusting nut allows swivel pressure to be regulated no more floppy filter wrenches Patent pending coating process adds many additional gripping points to securely grab the filter 50190 G asket Separator For Use on Any Application with a Gasket Seal Such as Oil Pans Transmission Pans and Differential Covers Drive tool between gasket and pan with a hammer Hardened carbon steel blade may be resharpened or replaced if damaged Blade is not warranted other than when new Shipping wt 12 oz 50200 Replacement Blade 50220 Button Head Cap Screw Patent D463 243 Patent Pending TM 57010 E xtra Small 2 375 2 625 60 3 66 7mm Range For small oil and fuel filters Special narrow 1 2 band fits in tight spots Shipping wt 12 oz 57020 S mall 2 875 3 25 73 82 5mm Range Fits a common smaller filter size found on many domestic and foreign vehicles Shipping wt 12 oz 57030 S tandard 3 5 3 875 88 9 98 4mm Range Fits most popular 3 625 standard filters Shipping wt 13 oz 57040 L arge 4 125 4 5 104 7 114 3mm Range Fits most tractors and other farm implement products Shipping wt 13 oz Gripping Texture Tension Adjusting Nut Swivels More Than 180 TM TM TM TM 66 PAGENew Tools 60850 M aster Triple Square Bit Set Nine Piece Triple Square 12 point Bits to Fit 4 5 6 8 10 12 14 16 and 18mm Sizes For head bolts brake caliper bolts door handle screws axle bolts and other applications The 4 and 5mm bits have 5 16 hex drive The 6 8 10 and 12mm bits have 1 2 hex drive The 14 and 16mm bits have 5 8 hex drive The 18mm bit has a 3 4 hex drive The three largest sizes are designed to work on tamper proof applications Shipping wt 15 oz 60710 4mm Triple Square Bit 60720 5mm Triple Square Bit 60760 6mm Triple Square Bit 60770 8mm Triple Square Bit 60780 10mm Triple Square Bit 60790 12mm Triple Square Bit 60860 14mm Triple Square Bit 60870 16mm Triple Square Bit 60880 18mm Triple Square Bit 40750 P arking Brake Cable R emover Allows Technician to Remove Parking Brake Cable by Compressing the Spring Tool can be used when cable is still attached to parking brake assembly Ends of tool are angled to allow easier access Slots on each end allow tool to slip over cable instead of feeding the cable through the end of the tool Especially useful on Ford F Series Expeditions Excursions etc Shipping wt 5 oz 51300 P arking Brake Adjusting S poon for Ford Trucks Double Ended Tool Speeds Star Wheel Adjusting on Ford F 150 Also Works on F 250 F 350 Super Duty Trucks with Dana 80 Rear Axles Tool adjusts star wheel through access slot in backing plate Squared tip works on F 250 and F 350 Angled tip with cutout for extra clearance works on F 150 pickups Use on drum in hat parking brake mechanism that is mounted inside the disc brake assembly Shipping wt 9 oz 51400 B rake Adjustment T ool for Ford Works from the Top to Speed Star Wheel Adjusting on 2001 2006 Ford Taurus Windstar and Mercury Sable and Other Drum Brakes with Top Mounted Adjuster Insert tool through slot in backing plate Angled ends for easy access Shipping wt 3 oz Supersedes 40800 Over Bent for Easier Access PAGE 67New Tools 38210 H ub Remover Kit for D odge Separates the Frozen Hub Assembly from the Steering Knuckle on Dodge Vehicles Tool drives against loosened retaining bolts to separate assembly Prevents damage to the knuckle and complete hub assembly Tool drives on the bolt flange so the head of the retaining bolt is not destroyed Kit contains 39300 for older smaller applications and 39250 for 2003 and newer 4 wheel drive 3 4 ton and 1 ton Dodge pickups Shipping wt 13 oz 39250 Hub Remover 03 09 Dodge 39300 Front Hub Knuckle Separator Patent 6 481 084 20000 M12 x1 25 Limited A ccess Spark Plug Chaser The Narrow Profile Allows Access to Spark Plug Holes in Confined Spaces Use with a 3 8 ratchet and locking extension For use on 2nd Generation Ford Triton Engines 2008 and newer Also for use on Mercedes Benz most V6 some V8 models newer than 2006 Nissan 2 0L 2007 and newer Toyota Scion 1 8L 2008 and newer Can also be used on some motorcycles lawn mowers snowmobiles and other small engine applications Size M12x1 25 Shipping wt 3 oz 46700 T ie Rod Puller for Ford For Use on 2002 and Newer Ford SUVs with Independent Rear Suspension Removes tie rod by inserting the angled tips between the tie rod and boot Use with a slide hammer to pull rear suspension link or tie rod end from the rear knuckle assembly Helps eliminated damage to tie rods by pulling straight out rather than prying or hitting the tie rod with a hammer Shipping wt 11 oz 71200 Stud Remover Removes Studs from Engine Blocks Exhaust Manifolds Cylinder Heads and Other Applications Allows for easy removal of studs Tool has two holes 1 2 14mm and 3 4 19mm for optimum fit minimizing damage to threads Range 3 8 10mm 3 4 19mm Design allows tool to grip flush with mounting surface of the stud so it can grab studs that are broken off very close to the mounting surface Use with 1 2 square drive Shipping wt 20 oz 39250 39300 Patent 6 874 549 68 PAGENew Tools 41270 I nput Shaft Alignment Tool Works on Manual and Electronic Shift Transmissions in Heavy Duty Trucks with 1 3 4 and 2 Splined Shafts Tool is inserted through the inspection plate and onto the input shaft between the clutch brake and clutch forks Tabs on spring loaded tool fit securely between splines to avoid damaging shaft Spring action adjusts to fit spline snugly Align transmission by turning the shaft to line up with the clutch brake Allows job to be done by a single technician Shipping wt 7 oz 19122 T ruck Drain on Wheels with Cover Now Includes a Snap In Cover Use this heavy duty drain to drain large capacity crank cases Holds 60 quarts Equipped with 4 rollers and a handle for transport and positioning under trucks Cover and curved side design help keep oil from spilling during movement Convenient handles and pour spout facilitate oil evacuation Rolls under most cab over axles so oil can be changed without jacks or jack stands Overall height 10 width 24 1 2 length 43 Cover may fit loosely and not snap into place on older 19122 Truck Drain models Shipping wt 22 lb 19172 Replacement Roller 57920 B attery Carrying Strap Makes Carrying Side Mount and Top Terminal Batteries Safe and Easy Heavy duty 14 plastic strap resists damage from battery acid The ends of the strap are marked for easy identification of positive and negative terminals The built in studs can also be used to attach a charger to side mounted terminals Shipping wt 7 oz Threads Into Side mount Terminals Carrying Top Terminal Battery Molded Tabs Help Keep Cover In Place Truck Drain Cover Charging Side mount Terminal Battery
