PDF associated:
/Fuel Injection Cleaner.pdf
MATERIAL SAFETY DATA SHEET SECTION 1 CHEMICAL PRODUCT COMPANY IDENTIFICATION PRODUCT NAME Fuel Injection Cleaner STOCK NUMBER CRB 2 18480 CRB 2 18479 CSF55 CSF54 SL110 1G Distributor Date Issued 4 1 09 Standard Motor Products Inc Supercedes 8 1 06 7070 Golf Course Drive Disputanta VA 23842 Information Telephone 804 862 1500 Emergency Telephone 804 862 1500 SECTION 2 COMPOSITION INFORMATION ON INGREDIENTS MATEIRIAL CAS BY WEIGHT Petroleum hydrocarbon solvent 64742 47 8 42 Hydrotreated middle naphthenic distillate 64742 46 7 50 Additive Proprietary 8 SECTION 3 HAZARDS IDENTIFICATION EFFECTS OF OVEREXPOSURE EYE CONTACT This material may cause mild eye irritation Direct contact with the liquid or exposure to vapors or mists may cause stinging tearing and redness EFFECTS OF OVEREXPOSURE SKIN CONTACT This material is a skin irritant Direct contact or exposure to vapors or mists may cause redness and burning drying and cracking of the skin and skin damage No harmful effects have been demonstrated in skin absorption studies Persons with pre existing skin disorders may be more susceptible to the effects of this material EFFECTS OF OVEREXPOSURE INHALATION This material is expected to have a low degree of toxicity by inhalation Breathing high concentrations of vapors or mists may cause irritation of the nose throat and signs of nervous system depression e g headache drowsiness dizziness loss of coordination and fatigue Respiratory symptoms associated with pre existing lung disorders e g asthma like conditions may be aggravated by exposure to this material EFFECTS OF OVEREXPOSURE INGESTION While this material has a low degree of toxicity ingestion of excessive quantities may cause irritation of the digestive tract and signs of nervous system depression e g headache drowsiness dizziness loss of coordination and fatigue Aspiration hazard This material can enter lungs during swallowing or vomiting and cause lung inflammation and damage COMMENTS This material has not been identified as a carcinogen by NTP IARC or OSHA Reports have associated repeated and prolonged occupational overexposure to solvents with permanent brain and nervous system damage sometimes referred to as 2 solvent or painter s syndrome Intentional misuse by deliberately concentrating and inhaling this product may be harmful or fatal This product is sometimes used as a dry cleaning solvent Retained solvent in absorbent clothing e g shoulder pads that remains in contact with the skin for prolonged periods has caused severe skin irritation including redness swelling burns and severe skin damage Care must be taken to ensure that garments cleaned with solvents are completely dry before being worn SECTION 4 FIRST AID MEASURES CAUTION Causes skin irritation Aspiration hazard if swallowed Can enter lungs and cause damage Combustible liquid and vapor Keep away from heat sparks flames or other sources of ignition e g static electricity pilot lights mechanical electrical equipment Keep container tightly closed Use with adequate ventilation Do not pressurize cut weld braze solder grind or drill on or near container Empty container contains residue liquid and or vapor and may explode in heat of a fire Open container slowly to relieve any pressure Bond and ground all equipment when transferring from one vessel to another Avoid contact with skin and clothing Wash thoroughly after handling Do not taste or swallow FIRST AID EYE CONTACT If irritation or redness develops move victim away from exposure and into fresh air Flush eyes with clean water If symptoms persist seek medical attention FIRST AID SKIN CONTACT Remove contaminated shoes and clothing and flush affected area s with large amounts of water If skin surface is damaged apply a clean dressing and seek medical attention If skin surface is not damaged cleanse the affected area s thoroughly by washing with mild soap and water If irritation or redness develops seek medical attention FIRST AID INHALATION If respiratory symptoms develop move victim away from source of exposure and into fresh air If symptoms persist seek medical attention If victim is not breathing immediately begin artificial respiration If breathing difficulties develop oxygen should be administered by qualified personnel Seek immediate medical attention FIRST AID INGESTION Aspiration hazard Do not induce vomiting or give anything by mouth because this material can enter the lungs and cause severe lung damage If victim is drowsy or unconscious place on the left side with the head down If possible do not leave victim unattended Seek medical attention 3 SECTION 5 FIRE FIGHTING MEASURES FLASH POINT 181 F PMCC LOWER EXPLOSIVE LIMIT 1 0 UPPER EXPLOSIVE LIMIT 7 0 EXTINGUISHING MEDIA Dry Chemical Carbon Dioxide Halon Foam or Water Spray UNUSUAL FIRE EXPLOSION HAZARDS This material is combustible and may be ignited by heat sparks flames or other sources of ignition e g static electricity pilot lights or mechanical electrical equipment May create vapor air explosion hazard if heated Vapors are heavier than air and may accumulate in low areas If container is not properly cooled it may explode in the heat of a fire SPECIAL FIRE FIGHTING PROCEDURES Wear appropriate protective equipment including respiratory protection as conditions warrant See Section IV Stop spill release if it can be done without risk Move undamaged containers from fire area if it can be done without risk Water spray may be useful in minimizing or dispersing vapors and cooling equipment exposed to heat and flame Avoid spreading burning liquid with water used for cooling purposes SECTION 6 ACCIDENTAL RELEASE MEASURES STEPS TO BE TAKEN IN CASE MATERIAL IS RELEASED OR SPILLED Combustible Keep all sources of ignition away from spill release Stay upwind and away from spill release Isolate hazard area and limit entry to authorized personnel Stop spill release if it can be done without risk Wear appropriate protective equipment including respiratory equipment as conditions warrant See Section IV Prevent spilled material from entering sewers storm drains other unauthorized treatment drainage systems and natural waterways Dike far ahead of spill for later recovery or disposal Spilled material may be absorbed into an appropriate absorbent material Notify fire authorities and appropriate federal state and local agencies Immediate cleanup of any spill is recommended If spill of any amount is made into or upon U S navigable waters the contiguous zone or adjoining shoreline notify the national response center Phone Number 800 424 8802 SECTION 7 HANDLING STORAGE HANDLING AND STORAGE PRECAUTIONS Keep container s tightly closed Open container slowly to relieve any pressure Use and store this material in cool dry well ventilated areas away from heat and all sources of ignition Post area No Smoking or Open Flame Bond and ground all equipment when transferring from one vessel to another Store only in approved containers Keep away from any incompatible materials See section 5 Protect container s against physical damage The use of explosion proof equipment is recommended and may be required see appropriate fire codes Do not enter confined spaces such as tanks or pits without following proper entry procedures such as ASTM D 4276 Outdoor or detached storage is preferred Indoor storage should meet OSHA standards and appropriate fire codes The use of respiratory protection is advised when concentrations exceed any established exposure limits see sections 1 and 4 4 Wash thoroughly after handling Do not wear contaminated clothing or shoes Use good personal hygiene practice Empty containers retain residue liquid and or vapor and can be dangerous Do not pressurize cut weld braze solder drill grind or expose such containers to heat flame sparks or other sources of ignition they may explode and cause injury or death Empty drums should be completely drained properly bunged and promptly shipped to the supplier or a drum reconditioner All other containers should be disposed of in an environmentally safe manner and in accordance with governmental regulations Before working on or in tanks which contain or have contained this product refer to occupational safety and health administration regulations ANSI Z49 1 and other governmental and industrial references pertaining to cleaning repairing welding or other contemplated operations SECTION 8 EXPOSURE CONTROLS PERSONAL PROTECTION VENTILATION If current ventilation practices are not adequate to maintain airborne concentrations below the established exposure limits See Section I additional ventilation or exhaust systems may be required Where explosive mixtures may be present electrical systems safe for such locations must be used RESPIRATORY PROTECTION The use of respiratory protection is advised when concentrations exceed the established exposure limits See Section I Depending on the airborne concentration use a respirator or gas mask with appropriate cartridges and canisters NIOSH approved if available or supplied air equipment EYE PROTECTION Approved eye protection to safeguard against potential eye contact irritation or injury is recommended PROTECTIVE GLOVES The use of gloves impermeable to the specific material handled is advised to prevent skin contact possible irritation and skin damage OTHER PROTECTIVE EQUIPMENT Impervious clothing should be worn as needed Eye wash and quick drench shower facilities should be available in the work area Thoroughly clean shoes and wash contaminated clothing before reuse SECTION 9 PHYSICAL CHEMICAL PROPERTIES BOILING POINT N E Air 1 VOLATILE 50 VAPOR DENSITY 5 2 APPEARANCE Gold Amber Liquid SOLUBILITY IN H20 Negligible ODOR Characteristic Amine Odor VAPOR PRESSURE 1 SPECIFIC GRAVITY 0 85 60 F 60 F N Butyl Acetate 1 BULK DENSITY N E EVAPORATION RATE N E SECTION 10 STABILITY REACTIVITY POLYMERIZATION CONDITIONS TO AVOID None Known 5 INCOMPATIBLE MATERIALS Avoid contact with strong oxidizing and reducing agents HAZARDOUS DECOMPOSITION PRODUCTS Combustion may yield carbon monoxide and or carbon dioxide HAZARDOUS POLYMERIZATION Will not occur REACTIVITY Stable under normal conditions of storage and handling CONDITIONS AFFECTING REACTIVITY Avoid all possible sources of ignition See Sections VII and VIII SECTION 11 DISPOSAL CONSIDERATIONS DISPOSAL METHOD Dispose of product in accordance with local county state federal regulations SECTION 12 TRANSPORTATION INFORMATION DOT PROPER SHIPPING NAME Combustible Liquid ID NUMBER N E DOT HAZARD CLASSIFICATION Combustible Liquid CHEMICAL FAMILY Hydrocarbon Mixture SECTION 13 OTHER INFORMATION HMIS RATINGS HEALTH 2 FLAMMABILITY 2 REACTIVITY 0 The information presented herein has been compiled from sources considered to be dependable and is accurate to the best of our knowledge however we make no warranty whatsoever expressed or implied of merchantability or fitness for the particular purpose regarding the accuracy of such data or the results to be obtained from the use thereof We assumes no responsibility for the injury to recipient or to third persons or for any damage to any property recipient assumes all such risks
